Find great deals for Kodak DryView Laser Imager Xray Film Processor Imaging System. Shop with confidence on eBay!. Find great deals for A Kodak DryView Laser Imager. Shop with confidence on eBay!. Kodak DryView Laser Imager with Kodak PACS Link Systems. This product implements all transactions required in the IHE Technical.

Author: Daizshura Arashiramar
Country: Papua New Guinea
Language: English (Spanish)
Genre: Science
Published (Last): 2 February 2014
Pages: 50
PDF File Size: 20.36 Mb
ePub File Size: 9.74 Mb
ISBN: 118-8-61414-719-6
Downloads: 41175
Price: Free* [*Free Regsitration Required]
Uploader: Yogar

DryView film is system-matched for AIQC—so imagers recognize film type, size, lot, and number of sheets remaining. Kodak DryView laser imager.

When set to ON, a print is automatically queued after the last image is stored the Print button does not have to be pressed. K Refer to local panel message. D 1 2 3 4 5 Figure Used to increase the contrast or density setting.

Kodak DryView 8700 Laser Imager Xray Film Processor Imaging System

Now in its fourth generation, the Kodak DryView continues to deliver the exceptional speed and diagnostic image quality that radiologists demand. Testing and Measurement Techniques — Section 8: Do not operate equipment with the covers open. Dashed lines indicate the film path. The Laser Imager also uses DryView film, but accepts only 11 x 14 in. D Laser Imager 1 Status: K Insert a different film cartridge and press the calibration button on the local panel.

The numbered descriptions correspond to the numbered callouts in Figure Testing and Measuring Techniques — Section Suction cups in the pickup area lift a single sheet of film out 870 the supply 87700 and feed it into the film transport rollers.

If this does not clear the error, turn the imager OFF, open the side door and check Area 3 for artifacts refer to pagethen turn the imager back ON. Mount the power strip on a wall or on the underside of a table. P Cannot read cartridge ID tag. K Call for service.


Output Button — Selects the desired output destination Imager 1 or Imager 2. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Repeat Steps 6 through 9 until the desired maximum density is achieved.

Kodak DryView 8700 manual

If an action message does not clear after performing the indicated action, call for service. The imager will need to be re–initialized. Status messages require no operator action. From 87700 Main Menu, press Imager Menu. Re–install the film cartridge and close the front door. Error Error messages indicate an error condition within the imager. You will automatically be sent an e-mail to inform you when someone has reacted to your question.

Attention Light — Indicates a condition that may affect imager operation e. Over time, this surface can collect dust.

Stop Print Button — Stops the most recently queued print job. Auf die Beobachtungsliste Ich beobachte Ihre Beobachtungsliste ist voll. Testing and Measurement Techniques — Section 5: Used to access the User 2 Settings menu. Warning When the power cord is plugged in, hazardous voltages are present in some areas of the imager.

Kodak Imation DryView Laser Imager Xray Film Processor | eBay

Ready Light — Indicates the imager is ready to begin its next operation. Environmental effects Heat load: The film transport drives the film up into the film developer. These menus are described later in this section. Now in its fourth generation, the Kodak DryView continues to deliver the exceptional speed and diagnostic image quality that radiologists demand. Artikel wurde bereits benutzt. Installation should require only a power outlet ddryview network connection.


D Rest of World: Use settings 1 through 15 for positive contrast images. Unprecedented speed and image quality ” Up to films per hour for maximum dryvied ” micron laser spot spacing, dpi resolution ” Continuous-tone images with up to 4, gray levels ” Consistent resolution from application to application ” 1: The accessory should provide fully automatic stitching software that delivers images up to 17 inches wide by 51 inches long 43 x cm.

Cleaning the Platen In some cases, error messages can be cleared by operator action, but in most cases a service call will be required.

Laser radiation may be present when the machine operates without panels or covers installed. Federal law restricts this device to the sale by, or on cryview order of, a licensed health care practitioner.

To remove the film cartridge, lift the edge of the cartridge slightly, then slide the cartridge out of the drygiew. K73 Refer to local panel message. Print the first image on a laser film in less than 90 seconds The system should be capable of supporting multiple users with optional remote operations panels, which can reprocess images if needed during review.

By using the ‘Select a language’ button, you can choose the language of the manual you want to view.