OSHA 29 CFR , which applies to the transmission, distribution, and generation of electricity, cites ASTM F shoes in the standards. ASTM F – Standard Specification for Dielectric Footwear has been updated. This specification covers acceptance testing of dielectric. All of Salisbury’s ASTM Dielectric Footwear conforms with ASTM F and all are % tested to the electrical hazard requirements of ASTM F at 20,

Author: Faetaur Gugore
Country: Cayman Islands
Language: English (Spanish)
Genre: Life
Published (Last): 26 May 2016
Pages: 449
PDF File Size: 17.7 Mb
ePub File Size: 10.2 Mb
ISBN: 569-9-35362-936-1
Downloads: 87923
Price: Free* [*Free Regsitration Required]
Uploader: Yosho

Minute holes in the soles of the footwear are the biggest area of concern in the protection scenarios. There are two basic names for shoes that have some protection from electrical shock: The differences between the standards are atm usually understood, even by electrical specialists.

Few guidelines exist on when and where to use the shoes in either standard. This paper offers some assistance on which standards relate to which shoes. An OSHA interpretation letter from March 17,basically does not “require” electrical trades to wear “safety toed shoes. OSHA states, “Electrical hazard, safety-toe shoes are nonconductive and will prevent the wearers’ feet from completing an electrical circuit to the ground. These shoes can protect against open circuits of up to volts in dry conditions and should be used in conjunction with other insulating equipment and additional precautions to reduce the risk of a worker becoming a path for hazardous electrical energy.

The insulating protection of electrical hazard, safety-toe shoes may be compromised if the shoes become wet, the soles are worn through, metal particles become embedded in the sole or heel, or workers touch conductive, grounded items.

Nonconductive footwear must not be used in explosive or hazardous locations. It is better in the sense that it does make use mandatory in a few cases but is still unclear about the role, if any, for EH shoes. Dielectric DI Shoes ” Where insulated footwear is used as protection against step and touch potential, dielectric overshoes shall be required. Insulated soles shall not be used as primary electrical protection.

Only dielectric footwear is listed in If they are for acid protection, then they would need asstm meet an applicable part of F In higher voltages or higher risks The ASTM F standard covers minimum requirements for the design, performance, testing, and classification of protective footwear. ASTM asstm must be marked with the specific portion of the standard with which it complies.

One shoe of each pair must be clearly and legibly marked stitched in, stamped on, pressure sensitive label, etc. M in this case means the footwear is designed for a Male F would be Female. I denotes impact resistance followed by the impact resistance rating 75 or 50 in foot-pounds.


ASTM F – 14a Standard Test Method for Determining Dielectric Strength of Dielectric Footwear

C denotes compression resistance and the compression resistance rating 75 or 50, which correlate to 2, pounds and 1, v1117 of compression, respectively. Mt means this shoe has metatarsal protection and rating 75 or 50 foot-pounds. Third and optional fourth line: The last two lines are used to identify footwear made to offer protection from other specific types of hazards referenced in the standard.

They designate conductive Cd properties, electrical insulation properties EHstatic electricity dissipative SDpuncture resistance PRchainsaw cut resistance CSand dielectric insulation DIif applicable.

The last line atsm used only when more than three sections apply.

Electrical Hazard EH footwear is manufactured with non-conductive, electrical shock-resistant soles and heels. The outsole can provide a secondary electrical shock resistance protection to the wearer against the hazards from an incidental contact with energized electrical circuits or parts.

Testing ensures the materials are capable of withstanding 14, v at 60 Hz xstm one minute with no current flow or leakage current in excess of 3. This is not usually acceptable for wet service or higher voltages. The CSA standard is also a “wet sole test. It has three procedures that differ according to the section of the footwear tested. To purchase ASTM standards, see http: ASTM F Reapproved is the specification for dielectric footwear and is a quite stringent standard.

Only one boot and overshoe currently meets the F specification. The most important thing to be aware of is that ASTM F is a standard designed primarily for impact and compression protection. Some dielectric shoes cannot pass the compression portion of that standard because many are designed as overshoes and don’t have a steel toe, but the overshoes can be worn with compression-resistant shoes if needed.

Steel toes have never been shown to conduct electricity as long as the toe is zstm covered with the shoe material. ASTM F refers to the boots and overshoes as “supplementary protection” because the shoes have no “in-use” standard. In-use standards normally require re-testing, so shoes should never be relied on as primary protection. Which Standard Do I Choose? First, choose the protection level or specific standard you need: Dielectric or Electrical Hazard levels.

ASTM F1117 Dielectric

Second, choose the standard: Third, look into the unique hazards of the work environment. The higher the overshoe, the less likely it is that water, grass, or other energized materials contact the worker. F11117, look closely at the heel and sole design. This ff1117 especially true for climbing poles, ladders, and stairs. A deep heel is needed to climb safely, while the normal shallow heel works well for walking. Fit f117 the ease of donning and doffing the footwear warrant consideration, especially on overshoes.


Problems to Consider Most testing applies only to the sole of the footwear, which usually begins degrading quickly. Footwear, unlike the rubber gloves used for primary protection in utilities, has nothing to protect it from the effects of walking and from the effects of ozone and UV light. The makers and users of dielectric shoes point out this fact. They also note that some utilities attempt to lessen the chances of sole degradation by stamping a date on the footwear and replacing them sstm one year or less, depending on the frequency of f117.

All manufacturers and users recommend regular visual inspections and replacement when any sign of excessive wear exists. Summary With OSHA early documents falling on the side of EH shoes for electrical work, companies would do well t1117 consider them for all electrical aztm and other workers exposed to electrical hazards or damp locations.

High-risk tasks, environments, and medium and high voltages require more and more stable protection. He is the senior managing partner and co-founder of e-Hazard, a leading electrical safety training and consulting firm, and the founder of ArcWear, which does 90 precent of the world’s arc flash testing of protective apparel. He has trained over 50, line-workers, managers, and electricians at large electric users and electric utilities and is a featured speaker at safety conferences.

IndustrySafe Safety Management Software helps organizations to improve safety by providing a comprehensive toolset of software modules to help businesses identify trouble spots; reduce claims, lost days, OSHA fines; and more. When it comes to OSHA atsm there are always questions regarding the requirements and in and outs.

IndustrySafe is here to help. We put together this page with critical information to help answer your key questions about OSHA recordkeeping. When it comes to safety training, no matter the industry, there are always questions regarding requirements and certifications. Using Dielectric and Electrical Hazard Shoes Minute holes in the soles of the footwear are asstm biggest area of concern in the protection scenarios. By Hugh Hoagland Apr 01, There are two basic names for shoes that have some protection from electrical shock: An example of ASTM style markings for protective footwear is: